View AZ100EL16VOLR2_8330557.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

az10el16vo az100el16vo ecl/pecl oscillator gain st age and buffer with enable 1630 s. stapley dr., suite 125 ? mesa, arizona 85204 ? usa ? (480) 962-5881 ? fax (480) 890-2541 www.azmicrotek.com arizona microtek, inc. features ? 250ps propagation delay on q output ? high voltage gain vs. standard el16 ? for oscillator applications ? operating range of 3.0v to 5.5v ? available in 2x2 or 3x3mm mlp package ? 75k ? enable pull-down resistor description the az10/100el16vo is a specialized oscillator gain stage with a high gain output buffer including an enable. the q hg /q hg outputs have a voltage gain several times greater than the q/q outputs. the el16vo provides an enable input (en ) that allows continuous oscillator operation. when en is low or floating (nc), input data is passed to both sets of outputs. when en is high, the q hg /q hg outputs will be forced low/high respectively, while input data will continue to be passed to the q/q outputs. the en input can be driven with an ecl/pecl signal or a full supply swing cmos type logic signal. the el16vo also provides a v bb output for a crystal bias node. the v bb pin can support 1.5ma sink/source current. when used, the v bb pin should be bypassed to ground via a 0.01 f capacitor. any used output must have an external pull down resistor. for 3.3v operation, a 180 ? resistor to v ee is recommended if an ac coupled lo ad is present. at 5.0v, a 330 ? resistor is recommended for the ac load case. alternately, a 50 ? load terminated to v cc ? 2v may be driven directly. unused outputs may be left floating (nc). note: specifications in ecl/pecl tables are valid when thermal equilibrium is established. package availability package part no. marking mlp 8 (2x2x0.75) az100el16vonb tnb mlp 8 (2x2x0.75) t&r az100el16vonbr1 tnb mlp 8 (2x2x0.75) t&r az100el16vonbr2 tnb mlp 16 az10/100el16vol azm16j mlp 16 t&r az10/100el16volr1 azm16j mlp 16 t&r az10/100el16volr2 azm16j soic 8 az10el16vod azm10el16vo soic 8 t&r az10el16vodr1 azm10el16vo soic 8 t&r az10el16vodr2 azm10el16vo soic 8 az100el16vod azm100el16vo soic 8 t&r az100el16vodr1 azm100el16vo soic 8 t&r az100el16vodr2 azm100el16vo tssop 8 az10el16vot azt16vo tssop 8 t&r az10el16votr1 azt16vo tssop 8 t&r az10el16votr2 azt16vo tssop 8 az100el16vot azh16vo tssop 8 az100el16vot azh16vo tssop 8 t&r az100el16votr1 azh16vo tssop 8 t&r az100el16votr2 azh16vo die az10/100el16vox n/a
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 2 q hg q q d d en v bb q hg pin description pin function d/d data inputs q/q data outputs q hg /q hg data outputs w/high gain v bb reference voltage output en enable input v cc positive supply v ee negative supply absolute maximum ratings are those values beyond which device life may be impaired. symbol characteristic rating unit v cc pecl power supply (v ee = 0v) 0 to +8.0 vdc v i pecl input voltage (v ee = 0v) 0 to +6.0 vdc v ee ecl power supply (v cc = 0v) -8.0 to 0 vdc v i ecl input voltage (v cc = 0v) -6.0 to 0 vdc i out output current ? continuous ? surge 50 100 ma t a operating temperature range -40 to +85 c t stg storage temperature range -65 to +150 c 10k ecl dc characteristics (v ee = -3.0v to -5.5v, v cc = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1080 -890 -1020 -840 -980 -810 -910 -720 mv v ol output low voltage 1 -1950 -1650 -1950 -1630 -1950 -1630 -1950 -1595 mv v ih input high voltage d/d en -1230 -1230 -890 v cc -1170 -1170 -840 v cc -1130 -1130 -810 v cc -1060 -1060 -720 v cc mv v il input low voltage d/d en -1950 v ee -1500 -1500 -1950 v ee -1480 -1480 -1950 v ee -1480 -1480 -1950 v ee -1445 -1445 mv v bb reference voltage -1430 -1300 -1380 -1270 -1370 -1250 -1310 -1190 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 40 40 40 40 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. truth table en q/q q hg q hg low or nc data data data high data low high nc = no connect
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 3 10k lvpecl dc characteristics (v ee = gnd, v cc = +3.3v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 2220 2410 2280 2460 2320 2490 2390 2580 mv v ol output low voltage 1,2 1350 1650 1350 1670 1350 1670 1350 1705 mv v ih input high voltage d/d 1 en 2070 2070 1 2410 v cc 2130 2130 1 2460 v cc 2170 2170 1 2490 v cc 2240 2240 1 2580 v cc mv v il input low voltage d/d 1 en 1350 v ee 1800 1800 1 1350 v ee 1820 1820 1 1350 v ee 1820 1820 1 1350 v ee 1855 1855 1 mv v bb reference voltage 1 1870 2000 1920 2030 1930 2050 1990 2110 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current d/d en 3 0.5 -300 0.5 -300 0.5 -300 0.5 -300 a i ee power supply current 40 40 40 40 ma 1. for supply voltages other that 3.3v, use the ec l table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 3. specified with en forced to v ee . 10k pecl dc characteristics (v ee = gnd, v cc = +5.0v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 3920 4110 3980 4160 4020 4190 4090 4280 mv v ol output low voltage 1,2 3050 3350 3050 3370 3050 3370 3050 3405 mv v ih input high voltage d/d 1 en 3770 3770 1 4110 v cc 3830 3830 1 4160 v cc 3870 3870 1 4190 v cc 3940 3940 1 4280 v cc mv v il input low voltage d/d 1 en 3050 v ee 3500 3500 1 3050 v ee 3520 3520 1 3050 v ee 3520 3520 1 3050 v ee 3555 3555 1 mv v bb reference voltage 1 3570 3700 3620 3730 3630 3750 3690 3810 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current d/d en 3 0.5 -1400 0.5 -1400 0.5 -1400 0.5 -1400 a i ee power supply current 40 40 40 40 ma 1. for supply voltages other that 5.0v, use the ec l table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 3. specified with en forced to v ee .
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 4 100k ecl dc characteristics (v ee = -3.0v to -5.5v, v cc = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1085 -1005 -880 -1025 -955 -880 -1025 -955 -880 -1025 -955 -880 mv v ol output low voltage 1 -1900 -1695 -1555 -1900 -1705 -1620 -1900 -1705 -1620 -1900 -1705 -1620 mv v ih input high voltage d/d en -1165 -1165 -880 v cc -1165 -1165 -880 v cc -1165 -1165 -880 v cc -1165 -1165 -880 v cc mv v il input low voltage d/d en -1810 v ee -1475 -1475 -1810 v ee -1475 -1475 -1810 v ee -1475 -1475 -1810 v ee -1475 -1475 mv v bb reference voltage -1400 -1260 -1400 -1260 -1400 -1260 -1400 -1260 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 40 40 40 46 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. 100k lvpecl dc characteristics (v ee = gnd, v cc = +3.3v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 2215 2295 2420 2275 2345 2420 2275 2345 2420 2275 2345 2420 mv v ol output low voltage 1,2 1400 1605 1745 1400 1595 1680 1400 1595 1680 1400 1595 1680 mv v ih input high voltage d/d 1 en 2135 2135 1 2420 v cc 2135 2135 1 2420 v cc 2135 2135 1 2420 v cc 2135 2135 1 2420 v cc mv v il input low voltage d/d 1 en 1490 v ee 1825 1825 1 1490 v ee 1825 1825 1 1490 v ee 1825 1825 1 1490 v ee 1825 1825 1 mv v bb reference voltage 1 1900 2040 1900 2040 1900 2040 1900 2040 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current d/d en 3 0.5 -300 0.5 -300 0.5 -300 0.5 -300 a i ee power supply current 40 40 40 46 ma 1. for supply voltages other that 3.3v, use the ec l table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 3. specified with en forced to v ee .
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 5 100k pecl dc characteristics (v ee = gnd, v cc = +5.0v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 3915 3995 4120 3975 4045 4120 3975 4045 4120 3975 4045 4120 mv v ol output low voltage 1,2 3100 3305 3445 3100 3295 3380 3100 3295 3380 3100 3295 3380 mv v ih input high voltage d/d 1 en 3835 3835 1 4120 v cc 3835 3835 1 4120 v cc 3835 3835 1 4120 v cc 3835 3835 1 4120 v cc mv v il input low voltage d/d 1 en 3190 v ee 3525 3525 1 3190 v ee 3525 3525 1 3190 v ee 3525 3525 1 3190 v ee 3525 3525 1 mv v bb reference voltage 1 3600 3740 3600 3740 3600 3740 3600 3740 mv i ih input high current d/d en 60 150 60 150 60 150 60 150 a i il input low current d/d en 3 0.5 -1400 0.5 -1400 0.5 -1400 0.5 -1400 a i ee power supply current 40 40 40 46 ma 1. for supply voltages other that 5.0v, use the ec l table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 3. specified with en forced to v ee . ac characteristics (v ee = -3.0v to -5.5v; v cc = gnd or v ee = gnd, v cc = +3.0v to +5.5v) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit t plh /t phl propagation delay d to q/q outputs (se) d to q hg /q hg outputs (se) 400 700 400 700 400 700 430 780 ps t skew duty cycle skew 1 (se) 5 5 20 5 20 5 20 ps v pp (ac) minimum input swing 2 150 150 150 150 mv t r /t f output rise/fall times (20% ? 80%) 100 350 100 350 100 350 100 350 ps 1. duty cycle skew is the difference between a t plh and t phl propagation delay through a device. 2. v pp is the minimum peak-to-peak differential input swing for which ac parameters are guaranteed. the device has a voltage gain of 20 to q/q outputs and a voltage gain of 100 to q hg /q hg outputs.
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 6 timing diagram d q en q hg 4 3 2 1 d 8 5 6 7 q en d / v bb v cc q hg q hg v ee tssop 8 soic 8 mlp 16 package and die: 10k/100k selection connect pin/pad 10k to v ee to select 10k operation. float (nc) pin/pad 10k to select 100k operation. v ee connection must be less than 1 ? . pin 6 of the mlp 16 package may be connected to pin 7 (v ee ) with no effect on the circuit. d q en v ee q hg q hg v cc 4 3 2 1 58 7 6 10 9 12 11 v bb q d nc 13 14 15 16 nc nc nc nc 10k mlp 16, 3x3 mm top view d 4 3 2 1 6 5 8 7 mlp 8, 2x2mm q hg q hg en q v bb v ee v cc top view
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 7 az10/100el16vo die: note: other die thicknesses available. cont act factory for further information. pad center coordinates name pad designation x(microns) y(microns) a d -342.5 312.5 b d -342.5 144.5 c v bb -342.5 -87.0 d en -342.5 -255.0 e v ee -33.5 -312.5 f 10k 126.5 -312.5 g q hg 312.5 -248.5 h q hg 312.5 -98.5 i nc 312.5 51.5 j v cc 312.5 201.5 k v cc 302.5 342.5 l q 142.5 342.5 m q -140.5 342.5 nc = no connect, leave open. a m lk j i h g f e d c b die size: 950u x 940u bond pad: 85u x 85u die thickness: 14 mils el16vo die pad coordinates
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 8 package diagram mlp 8 dual 2x2mm bottom view side view mlp 8 (2x2mm) 2.0000.050 2.0000.050 pin 1 dot by marking 0.3500.050 pin 1 identification r0.100 typ 1.750 ref. 1.2000.050 exp. pad 1 2 3 4 5 6 7 8 0.2500.050 0.500 bsc 0.6000.050 exp. pad 123 4 0.7500.050 0.000-0.050 0.2030.025 top view note: all dimensions are in mm
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 9 millimeters inches dim min max min max a 0.75 0.069 a 1 0.10 0.25 0.004 0.010 a 2 1.25 1.45 0.049 0.057 a 3 0.25 0.01 b p 0.36 0.49 0.014 0.019 c 0.19 0.25 0.0075 0.0100 d 4.8 5.0 0.19 0.20 e 3.8 4.0 0.15 0.16 e 1.27 0.050 h e 5.80 6.20 0.228 0.244 l 1.05 0.041 l p 0.40 1.00 0.016 0.039 q 0.60 0.70 0.024 0.028 v 0.25 0.01 w 0.25 0.01 y 0.10 0.004 z 0.30 0.70 0.012 0.028 0 o 8 o 0 o 8 o notes: 1. dimensions d and e do not include mold protrusion. 2. maximum mold protrusion for d is 0.15mm. 3. maximum mold protrusion for e is 0.25mm. package diagram soic 8
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 10 package diagram tssop 8 millimeters dim min max a 1.10 a 1 0.05 0.15 a 2 0.80 0.95 a 3 0.25 b p 0.25 0.45 c 0.15 0.28 d 2.90 3.10 e 2.90 3.10 e 0.65 h e 4.70 5.10 l 0.94 l p 0.40 0.70 v 0.10 w 0.10 y 0.10 z 0.35 0.70 0 o 6 o notes: 1. dimensions d and e do not include mold protrusion. 2. maximum mold protrusion for d is 0.15mm. 3. maximum mold protrusion for e is 0.25mm.
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 11 package diagram mlp 16 millimeters dim min max a 0.80 1.10 a1 0.00 0.05 a3 0.25 ref b 0.225 0.275 d 2.90 3.10 d2 1.65 1.95 e 2.90 3.10 e2 1.65 1.95 e 0.50 bsc l 0.35 0.45 aaa 0.25 bbb 0.10 ccc 0.10 notes 1. dimensioning and tolerancing conform to asme t14-1994. 2. the terminal #1 and pad numbering convention shall conform to jesd 95-1 spp-012. 3. dimension b applies to metallized pad and is measured between 0.25 and 0.30mm from pad tip. 4. coplanarity applies to the exposed pad as well as the terminals.
az10el16vo az100el16vo august 2003 * rev - 6 www.azmicrotek.com 12 arizona microtek, inc. reserves the right to change circuitry a nd specifications at any time without prior notice. arizona mic rotek, inc. makes no warranty, representation or guarant ee regarding the suitability of its products for any particular purpose, nor does a rizona microtek, inc. assume any liability arising out of the applica tion or use of any product or ci rcuit and specifically disclaims any and all liability, including without limitation special, consequential or inci dental damages. arizona microtek, inc. does not convey a ny license rights nor the rights of others. arizona microtek, inc. products are not designed, intended or authorized for use as component s in systems intended to support or sustain life, or for any other applicati on in which the failure of the arizona microtek, inc. product co uld create a situation where personal injury or death may occur. should buye r purchase or use arizona microtek, inc. products for any such unintended or unauthorized application, buyer shall indemnify a nd hold arizona microtek, inc. a nd its officers, employees, subs idiaries, affiliates, and distributor s harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim al leges that arizona microtek, inc. was negligent regarding the design or manufacture of the part.

▲Up To Search▲

Price & Availability of AZ100EL16VOLR2

	To Download AZ100EL16VOLR2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .